Here comes the Fiat and Lancia immobilizer key programming list of Lonsdor K518ISE/K518S key programmer.
(Note: Models update till June 2019. Keep updating. Functions marked red below are under subscribed menu)
Fiat IMMO Vehicle List
Lancia Vehicle List
Lonsdor K518ISE review on Fiat: Lonsdor K518ISE reads PIN for older Fiat 2005-2012 Lonsdor K518ISE Read Fiat Freemont Pin Code and Add Smart Key Success
Hi all,
After going through the nightmare of using my FVDI to read a pin code from Johnsons BSI and then causing BSI to go into Boot mode I have come up with this solution for any users with similar issues.
There is 2 ways of retrieving pin code from BSI:
1st is from OBD – this is the operation that is risky 60/40 chance of causing BSI to go into Boot Mode.
2nd is from direct read(BSI not opened up) with BSI removed – this works 100% of the time.
Solution 1: OBD read
This operation can only be done WITHOUT vehicle in Economy mode. Run engine for 15 minutes to give charge into battery. Attach battery charger. Disconnect both headlight connectors & remove wiper motor fuse(usually no.12 in engine fuse box). All doors closed & no power consumers on. Use Diagbox to deactivate economy mode in BSI – If option available. Use FVDI to read pin code.
THE REASON BSI GOES INTO BOOT MODE IS BECAUSE ‘ECONOMY MODE’ ACTIVATED DURING THE PIN CODE RETRIEVAL.
I’ve also used same procedure to change kilometres in instrument cluster/BSI and works okay.
Solution 2: Direct read
Remove the BSI from vehicle. Attach BSI on bench. Before reading pin the information from BSI can be recorded incase anything goes wrong during procedure. Use Diagbox/PPS to record configuration in BSI – BSI/REPAIR/CONFIGURATION/MANUAL CONFIGURATION then screenshot all of the options in each section. Use Diagbox to deactivate economy mode in BSI – If option available.
Use FVDI to record flash & configuration using “BSI EXCHANGE” – Read BSI only. This flash will now be stored in folder PSA in documents.
You can now use FVDI to read pin.
BSI RECOVERY: Boot mode
If the BSI has went into Boot mode then the existing flash in BSI has been corrupted. Reflash using FVDI with flash recorded in PSA folder.
If you haven’t got a saved flash then you will need to get a good flash for BSI from the helpful people on this site. Once flash has been loaded onto BSI the pin code & configuration will be lost from its memory. Relearn pin code to BSI with DIAGBOX & learn keys – configure BSI if necessary.
attachment: how to connect BSI johnson control on table
Let’s starts with some frequently asked questions on the Benz FBS3 BGA keyless Go Key.
I buy this keyless go key, How to write via usb ?
The key is not reusable.
The key is connected by USB for data read and write.
As long as you can read the Ignition Switch’s data and collect the correct password, the key can match the same function as the OEM keyless go.
Supported models:
S-W221(2010-2013) GL-W164(2010-2012) ML-W164(2010-2012) R-W251(2010-2017)
S series W221 W216: YES!
ML/G/R series W164 W251: YES! 2010-2014 C & E series: NO! Compatible with VVDI MB tool
Additional information:
Frequency: 433MHz
Write by IR vehicle coverage: Mercedes with FBS3 system after year 2009
The key does not come with battery.
The key can be programmed as normal key.
This 3-button Smart key shell is recommended to use with the key.
How to use the Benz FBS3 KeylessGo Smart Key?
1. Install battery before write key and test all key buttons.
2. Only allowed upload V51 version key data. (If VVDI MB fails to write key via IR, it is normal)
3. Remove battery before get in car and activate key. Insert and unplug key for 5-6 times every 5 seconds. If the key can start vehicle, install battery, test the remote control and keyless go function.
FBS3 key USB connection wiring diagram
The MBSmartKeyTool software is required when write key via USB
Software can be download here for free: https://mega.nz/#!3nRFiaSR!cx5h7n0ebe9koeI6gJHZ_quZldJ-JvOO1vYwhl_WOd0
Read EIS data and collect correct password, then write a key.
Done.
WiFi JLR DoIP VCI is compatible with original SDD and Pathfinder software. But it uses it own driver. Here you can download software and driver for doip vci for free.
Note: The follow software and driver is for DoIP VCI clone (Item No. SP312).
Support Pathfinder for JLR 2017 up
Support SDD for JLR -2016 Support SDD online programming Support Pathfinder online key programming Support SDD engineering software Support Pathfinder engineer software Support EXML edit Support VBF edit
Free Download SDD software for DoIP VCI
http://diagnosticdelivery.jlrext.com/idscentral
Free Download Pathfinder software for DoIP VCI
http://diagnosticdelivery.jlrext.com/pathfinder/Jaguar_Land_Rover_Connect_Updater_v2.exe
(it will take you about 2 or 3 days to download the complete data of PathFinder with network continuously.)
Or visit official website http://www.autosos.com.cn to download software
Go to Technical Support->SDD & Pathfinder Download, and download SDD or Pathfinder one by one
How to install driver for JLR DoIP VCI interface?
Free Download JLR DoIP driver VCI Manager(JLR) 19.04.28.exe
password: g0f0
Please pay more attention to the version of the DoIP VCI driver. It should always be the latest version. So you should update the driver without delay.
The above driver 19.04.28 driver is the current version (Aug. 2019). If newer version driver released, you can download latest version on official website as well (check picture below).
The connection of DOIP VCI
Connect with USB; (It’s easy)
Connect with WIFI; (You can choose the Wifi named “DoIP-VCI-11D4”, and the last four numbers are in random.)
The Connection between the DoIP VCI and computer
Following the picture below, open the VCI Manager and click the “connect”
Check the connection status with the computer.
When it shows a green check mark, VCI is detected
Update of DoIP VCI’ firmware.
Open“VCI manager”
Then click the “VCI Update”
Click the “Start” and you can check the update progress on the right
Attention:
When you click the “start”, vci cannot be interrupted or stopped. Otherwise the JLR DoIP VCI will be damaged. You can disconnect when it finished.
SDD can get the hardware directly, it’s perfect if the icon is green.
PathFinder need to set the network interface.
Log in with account firstly,
( If you have Pathfinder account you can login directly. You can contact JLR VCI factory engineer for help if you don’t have an account. Email: [email protected])
Click “cancel”
It doesn’t connect successfully if it shows “SIM” “SimFiles”, you should select the communication interface as “JLR-JLR-DoIP, D-PDU API by Bosch” and VCI serial “86004905”. Now you can use it for diagnosis.
Now Pathfinder software is ready to use.
Purpose: transponder key copy
Car model: VW Jetta
Car year: 2008
Transponder: Megamos ID48
Device: Autel MaxiIM IM508
Steps:
go to autel im508 immo system
accept the disclaimer
go to im508 volkswagen software
smart mode
reading vehicle information
read out the vehicle
it’s jetta 2008
information:
“remote control learning” function will first clear all working remotes, then learn remotes available. before using these functions, pls ensure that all keys are prepared.
“remote control add” function will add one remote to existing remote count. the customer can use there functions without all keys available.
copy megamos 48 key:
step 1: read immo data
step 2: read and write key id
step 3: make a dealer key
key copying success!
test the key on the car
the key is working!
job’s done!
Time: under 5 min
Result: success!
Conclusion:
Walk thru of the great feature built into the Autel IM508 and IM608 for cloning VW megamos id48 transponder keys.
Using the Scan tool you can clone a key ID to a new blank key saving time from pulling and decoding the PIN.
Everything can be done in under 5 Minutes. Volkswagen Audi Group.
New MB Star SD Connect C4 PLUS DoIP diagnostic multiplexer enables WiFi/WLAN and USB connections. Some of our Japanese customer reported that the doip c4 communicates fast and stable through WiFi. Check the step-by-step wifi setting guide below:
How to Configure mb sd c4 doip WiFi wireless connection?
Open Administration->SDConnect Toolkit
Select Register/configure tab
Enable both WLAN parameters, workshop and WLAN parameters, road option
Set up IP address, encryption type and key as following:
WLAN parameters, workshop
IP address: 192.168.191.31
Network screen: 255.255.255.0 Gateway: SSID (network name): workshop Encryption: WPA2/ASCII Key: 123456789
WLAN parameters, road
IP address: 192.168.2.223 Network screen: 255.255.255.0 SSID (network name): Road24h Encryption: WEP/Hex Key: aaaaaaaaaaaaaaaaaaaaaaaaaa (26*a) Press Start button
You’ll see WLAN and device status turn to yellow on toolbar
You are allow to print out the SDConnect Toolkit configuration settings as well
Close the MB SD C4 DoIP SDConnect Toolkit
Open and install Mars free WiFi Hotspot software on desktop
set the WiFi name as: workshop and password, then Save Restart the computer !!!! WiFi setting is done.
Now open the Xentry software on the desktop to start wireless diagnosis
i.e Runs a self-test on a Mercedes Benz C-class W204
See also:
How to Configure MB SD Connect C4 DoIP when diagnose DoIP models?
Is it the clone of genuine Bosch xentry VCI?
Does it require install VXDIAG drivers? Can it be used wirelessly? Do you use ordinary Xentry openshell or Xentry openshell pass-through?
Answer:1. They have not cloned the new Xentry VCI
2. You can use ordinary XDOS without VXdiag Driver. Only config ecom and ready. 3. With keygen. No wireless or wifi, usb and lan only.
The one looks like original, but inside is different. It works like Ecom.
Here some Pictures of Xentry VCI C6 Clone.
The inside boards:
Software contains xentry (not DAS), vediamo, dts, epc/wis.
Test on A class W177 and a Brabus, fast USB connection and able to access all possible modules.
Downside:
The Benz C6 VCI should work with only the software they produce which can be expensive when updating.
Suggestion:
In conclusion we think the SD Connect C4 represents better value for money for the novice user who should wait until they can use Xentry software with confidence before moving to more advanced Vehicle Communication Interface, The C6 VCI seen in the photo is what a good high quality clone should look like and not the VCM2 encased version which is of lower quality
We only stock the highest quality VCI call us for free consultation. |
AuthorCategories |