Q:
I want read/write eeprom from vdo cluster w211 from 2002 at table with vvdi mb bga tool. can’t do it in car. have access for odometer change only. need pin out if possible.
A:
Here’s the common pinouts to Mercedes-Benz.
1.Dashboards
W211, W219, W203, W209 Dashboard
W212, W218, W204, X204 Dashboard
W221, W216 Dashboard
W245, W169 Dashboard
SMART 451 Dashboard
2. Engine Control Units
ME9.7
MEG SMART 451
MEG SMART 450
SIEMENS SIM4LE
SIEMENS SIM4LKE
W168 VDO ECU and AIR-MASS
TEMIC ECU
EDC15C5 (CDI-1)
EDC15C6 (CDI-2)
EDC16C31
3. Other
Hybrid Unit (N129 Starter alternator) SMART 451
ESP SMART 451
ETC SMART 451
CGW W221/W216
CGW W164/W219/W211/W251/W169/W245
ETC W220/W215
Electronic Gear Selector Module (Waldhebelmodul) W220/W215
ISM (Intelligent Servo Module) W221/W216
SBC W211/W219
Q:
Does anyone have a list of command line arguments/parameters for starting mb star diagnostic SD Connect C4 HHT-Win directly from shortcuts? For example, I know that "HHTPKW.exe -b140" will start HHTWin for the W140 (gas version), and -b129 will start it for the R129. I'd be interested in other arguments or parameters that might be available, such as starting HHT for diesel variants directly.
I found a program that can extract these from 32bit programs, but HHTWin is 16bit, running in a virtual environment on x86 Windows, and the program won't work. A: Here it is: hht parameters for x32 and x64 WINx32Default: 32-bit operating system: run HHTWIN directlyPKW: CmdLine="hhtpkw.exe" Parameters: ‐Lnn language : ‐L02 ‐b baureihe : ‐b124, ‐b140, ‐b202, ‐b201, ‐b210, ‐b126, ‐b107 ‐m motor : ‐mB Benzin, ‐mD Diesel ‐wO8154711 ‐C dbname : ‐CPKWWIN.CDB ‐P dbpath : ‐PC:\PROGRA~1\MERCED~1\HHT\PKW\ ‐D Dialog : ‐D example how to use: hhtpkw.exe ‐b140 ‐mD ‐wO8154711 NFZ: CmdLine="HHTNFZ.EXE" Parameters: ‐n nfz ‐wO8154711 ‐b baureihe ‐C dbname : ‐CNFZWIN.CDB ‐P dbpath : ‐PC:\PROGRA~1\MERCED~1\HHT\NFZ\ ‐D Dialog : ‐D example how to use: HHTNFZ.EXE ‐n ‐wO8154711 ‐bSPRN WINx6464bit operating system: HHTWIN run via virtual machineCmdLine="HHTWIN_VM_Start.exe"
Parameter:
PKW: HHTWIN_VM_Start_PKW.bat NFZ: HHTWIN_VM_Start_NFZ.bat The batch file specified by the starter is specified as the parameter (Als Paramter wird die Batchdatei angegeben, die der Starter aufruft.) example how to use: HHTWIN_VM_Start.exe ‐HHTWIN_VM_Start_PKW.bat HHTWIN_VM_Start.exe ‐HHTWIN_VM_Start_NFZ.bat -w parameter, i'm not sure but it is always included in pkw or nfz. -D dialog of language hht vm is the most wanted program. it is made for x64 OS. DAS automatically set the correct OS, and choose the correct file to run.
Success! Xhorse VVDI Prog have reset/renewed BMW Key transponder PCF7953 (remote 868MHz).
And it’s confirmed by Tango key programming tool!
In detail…
Step 1: Tango reads key info
Read key information
Brand: BMW
Transponder: PCF 7935P
HITAG Family: HITAG-Pro
ID: xxxxxxxx
Key type: Keyless go
Immo type: Unknown
Remote: 868 MHz
VIN (1): WBAxxxxxxxxxxxxxxxxx
VIN (2): WBAxxxxxxxxxxxxxxxxx
Status: Learned
Mileage: 67268
CryptoKey: Customer (Locked)
Step 2: VVDI Prog resets protect
In VVDI-Prog:
Select chip: PCF7935 IN CIRCUIT
Wiring connection:
Reset Protect (will erase the chip data? Yes!)
Step 3: Tango reads key info
In Tango key programmer:
Read key information
Transponder not detect
Step 4: VVDIProg read & write key data
In VVDI-Prog :
Open eeprom and EROM bin files to read and write
Step 5: Tango reads key info
In Tango:
Read key information
Brand: BMW
Transponder: PCF 7935P
HITAG Family: HITAG-Pro
ID: xxxxxxxx
Key type: Keyless go
Immo type: Unknown
Remote: 868 MHz
VIN (1): *******************
VIN (2): *******************
Status: NOT Learned
Mileage: no DATA
CryptoKey: Factory (Unlocked)
Eeprom data
Ide and Cryto Key
Test Key: OK
Done!
strong>Purpose: To do W205 coding with MB star diagnostic SD connect C4 and DTS software
Vehicle: Mercedes-Benz W205
Hardware: SD connect c4 mux
Software: DTS Monaco
Where to get DTS:
You can get them like a package from ebay or amazon, or some OBD tools seller such as obdii365.com.
Recommendation: I am NOT recommend you to do any modification on your car by yourself before you fully understand how everything works, you could cause thousands of non fixable damage just by one misclick!
About Mercedes Coding: Software Calibration Number coding, short for SCN coding is intrudes by Mercedes Benz around 2005. It replaced the previous coding technique with a centralized and almost automated technique to prevent incorrect coding being selected when replacing a module. SCN Codes will now be able to be generated by authorized dealership personnel via any computer with internet access or any NetStar Terminal. This will be possible by the user accessing a secured website utilizing a log-on and password unique to the user. The user then will be able to generate an SCN Code using vehicle data as well as data from the replaced/flashed ECM.
The process:
The dashboard status
In DTS Monaco – Kurztest_205_odx:
Read and save data
Read ECU identification only
Clear codes and read data
Varianten_codieren:
Initialization: ECU
ECU: IC222 (uds_can_d)
Domain: [004] 04 Landeikodierung_scn schreiben
Done!
How to change KM on a Kia Cerato year 2010 using carprog.
Procedure: Remove dashboard IC from the car Open it and find internal EEPROM memory, select same from the list Use carprog A4, A5 or A6 (due to situation) adapter to connect to EEPROM In some cases you will need to remove (desolder) EEPROM from the board Open carprog software, select mileage function->KIA->AutoDetect-> select eeprom type from list;93C66,93LC66 16bit Select denso type and double click to open it You can read and save EEPROM first Enter mileage value you desire to change and press "Write KM" Change KM success. Read KM again If carprog prompts "no mileage found", go back to selection menu, Press Next, denso type and read again. It will display new odometer. Resolder the eeprom back to dashboard. Check the new mileage. http://www.obdii365.com
Here are tips and guides to help you get radio codes on a VAG vehicle.
Done with a VAS 5054A Bluetooth head and ODIS-S software!
Here you go…
In ODIS-service: select “Start Diagnosis”
In the Basic Vehicle Features, select “Manual” for the vehicle identification.
Select “Yes” to perform the diagnosis without guided fault finding
In “Model”, select “Previous Models for Immobilizer-Online”
This selection will automatically set all of the other selections as “All”.
Next, deselect “Work with Guided Fault Finding” box and press the “Apply” button.
vas 5054a ODIS will now run a quick check
Then the “Special Functions” tab will appear
Select “Special Functions” and you will see the “Checking Radio Code” test.
Go to “Perform Test”
Select “OK”
Steps will be carried out:
Input of vin
Input of component group id of radio
Output of radio-pin
Press the “Complete/Continue” button
Enter the VIN in the “Red” box and select “Accept”.
Enter the AUZ number in the “Red” box and select “Accept”.
Enter name in the “Red” box and select “Accept”.
Enter number in the “Red” box and select “Accept”.
Enter the country in the “Red” box and select “Accept”.
Next, data is transmitted online
To do this, a connection must be established:
– connect tester with respective hardware to online network
– next enter your user name and password
– press the “Complete/Continue” button.
Enter your GEKO ID information and select the “Apply” button.
After pressing the button the test will start.
The radio code retrieving test will go through a series of checks and steps in order to obtain the code. Some of the screens will show the following…….
The connection was established
Next, the data will be sent.
The data was transmitted.
The tester waits for data to be received.
The tester evaluates the received data.
After the connection is established and the tester retrieved the radio code, this next screen will show up with your number.
Press the Complete/Continue button to exit test.
Job’s done! Have good luck with ODIS for radio codes!
How to: reset/renew Mercedes Benz W164 Siemens VDO ISM using CGDI Prog MB key programmer on bench.
Follow cgdi prog wiring diagram to connect ISM unit with CGDI MB
In CGDI MB software, select Auto Computer, Module type W164->ISM/DSM/ESM
Read ISM information
Press Get to calculate erase password
Erase password calculated successfully
Press Erase
Reset ISM success
Done.
Jaguar, Land Rover Diagnostics tool software SDD released to newest version 155. Here obdii365.com provides software & patch free download resource.
Version: SDD V155
Year/Release Date: 11.2018
Multi Languages:
English, Dutch, Spanish, Italian, Chinese, Korean, German, Portuguese, Russian, French, Japanese
Operating system: Windows 7 32-bit (recommended. You are free to try other systems)
Supported hardware:
Dealer diagnostic for Land Rover Jaguar Works with VCM Rotunda/VCM2, with both original & clone.
Da-Dongle J2534 VCI (replaced VCM I)
JLR VCI (Jaguar Land Rover approved SAE j2534 Pass-Thru interface) JLR VCI (SP284) JLR DoiP VCI
J2534 EUCLEIA wiScan T6
SDD 155_FULL / SDD_155_154_UPDATE
NGI_Phase2.5_004.00.005 NGI_Phase2.5_004.01.001 NGI_Phase2.5_004.02.002 NGI_Phase2.5_004.03.002 NGI_Phase3_005.00.004 NGI_Phase3_005.01.003 NGI_Phase3_005.02.001 NGI_Phase3_005.03.001 NGI_Phase3_005.04.001 NGI_Phase3_005.05.002 NGI_Phase3_005.06.002 NGI_Phase3_005.07.003 NGI_Phase3_005.08.001 NGI_Phase3_005.09.001
Free Download JLR SDD V155 software
Free Download JLR SDD V155 patch
How to install and activate JLR mangoose SDD V154 software?
Main procedure:
1. JLR PanasonicScript-Setup does not need to be installed otherwise. When the installation is complete, the computer is in reboot.
2. Install SDD_155.00_FULL.exe at the end of the installation of the computer in a reboot. 3. Install all available software updates in numerical order , for example, “SDD 155.01.exe”. 4. Copy the patch to the desktop and launch the patch, wait for the window with confirmation of the successful completion of the procedure . That’s all. Run the program and begin to use. |
AuthorCategories |