How-to: read 2017 Hyundai Elantra pin code from 8A smart key with Autel MaxiIM IM608.
Connect PLC200 with vehicle via OBD socket. Pair PLC200 with KM100. Select Hyundai- Manual selection- Select region- Elantra (ADA)- 2017 If don’t not which Elantra to select from, select each one and check the year coverage Elantra (ADA) has 2017 year supported. Do an Immo status scan It will also read pin code from 47 smart card, make sure the type is correct Read pin code in process. Read pin succeed Now you can do smart key programming with the PIN code PCMTuner flash and KT200 (exactly the same as KTM200 or ECUTuner) which is better? First of all, check a table comparison below:
Which is better? KT200 is based on Geniune fgtech. Fgtech is the best for old cars, for newer you must doing in bench ot boot, no OBD. No OBD for sid208, no OBD for BMW Fxx, no OBD for new Nissan/Renault SID309/310 edc17c84. They updated bench for edc17 and bench for MD2 in the last 3 years. KT200 is quite the same, also the software as fgtech. Buy they released a lot of new ECUs and this tool can read and write a lot of TCUs. KT200 is galletto but with more new protocols and with the possibility of reading TCUs. on TCU they have much more than kess v2/dimsport. But in one tool you have OBD, BDM, Jtag, Boot and Bench mode. but for bdm you must use their adapter. It has edc16/med9/edc7 bench mode, and work very well. Pcmtuner is based on pcmflash software, it works pretty good on bench mode, boot and OBD. It has tuner account, free VR files and damaos for users. KT200 has more ECUs and TCUs supported, more protocols inside and has Jtag and BDM. But it don’t have tuner account, tuning service and wiring diagrams. 2010 Volkswagen Passat CC how do I do the eeprom on it with Autel MaxiIM Im608/IM508? Open board, desolder 95320 chip and read chip. You cannot read this chip in circuit. Solder 95320 chip to eeprom adapter and put adapter to xp400 or xp400pro programmer Before desoldering the chip, put a dot on one corner and take a picture so you know exactly how it goes back on. AUTEL IM508/IM608 Vw Passat b6 b7 cc add key (akl) via dump eeprom procedure: Select Write Key via Dump function Select Passat- >Comfort module 95320 (ID48)- >One-touch processing If you’ve tried to read the chip in circuit or it’s failed read as a 48 chip, make sure you desolder and try reading it as a 46 chip if it fails to read as a 48 once desoldered. Using pin code program remote function and start car to check all working. Done. http://www.key-programmer.org/2022/08/10/autel-im608-vw-passat-b6-b7-cc-add-key-via-dump/ We are doing all keys lost on Mercedes c300 2011 (W207) with the Autel MaxiIM IM608 through the Obd no need to remove the EIS. Only fobik AKL can be done via OBD in car. Not only W207, you can do other Mercedes new fobik via OBD, i,e Spinter DAS3 fobik.
Better check vehicle coverage on Autel website to see if OBD mode is available. Here’s the diagram you can see there’s a fuse cable you can make this work there ELV this one go to the obdii, another goes to the diagnostic tool connector. doing all keys lost on Mercedes c300 2011 (W207) with the Autel IM 608 through the Obd no need to remove the Eis. New fobik key programming You don’t have to use the ELV Simulator when doing all keys lost every time, just follow the diagram, it depends on the model not always the same. so we had to connect to this connector here the disconnect the EOP which is right above the brake pedal. You’re looking for this blue connector and then you connect on the pin number three with this cable. You follow it and connect to the g box here and then you gotta take out the fuse number 27 and use the fuse cable. it’s right here, left open the engine and this box everything’s hooked up. Connect the xp400 with autel im608. That should be okay all right. Let’s begin doing this model. Select model and on vehicle method Read EIS data Test key just follow im608 prompts step by step. PCMTuner Flash v1.2.7 adds new Fetrotech Plugin and new UI interface. This new upgrade will require you re-activate your device. Check guide below to download and install software 1.2.7.
Where to download PCMTuner 1.2.7? Go to Tuner-box.com to download new update complete with new pcmflash (PCMTuner Flash). Remember to always run setup as admin and disable any strict firewall etc. How to Activate PCMTuner 1.2.7? Send email your pcmtuner ID to [email protected] to get a registration key. 1 the first time of you run the pcmtuner flash will display a code, pls ctrl+v send to us according to the notice notice: always save and backup your license
Note: The device ID is not your serial number. The hardware ID can be found on the back of the pcmtuner. If earlier machines don’t have device ID on the back, please contact your supplier to get it activated. If after copying the REG key for PCMtuner flash and you still have problems, please set the Language regional settings as per these Images Change the language Unicode as world wide beta version, language Unicode as China simple (its Unicode not display language), then restart your laptop. Difference between pcmflash and pcmtuner flash? Name of software and credits inside it. No logo pcmflash. Not possible update Pcm flash v 1.20.
If get an error PCMTuner Flash Not Found, this is specific only if you have updated pcmtuner app and have the message cannot find pcmtuner flash Honda and Acura have a platform that you have to buy subscription from it. After purchase subscription and download software, you can use a Honda J2534 passthru device to do anything you want.
Part I: How to Buy it, Download it and Activate iHDS? So what you need to do first you have to have internet. You are gonna internet explorer you don’t go by google because when you pay the bill for the subscription it will not go through here. You can write Honda Tech Info, then you click you will get this Honda tech info on the express, click on Login Already have your login in, so you click OK Now here you click to get the subscription. You’re gonna scroll down. You choose 45$ for one day, $200 for 30 days or $1,800 for 365 days. You have got a login, you want to pay by Paypal or you want to pay by Credit car. Buy now after you put your information. You have to display also what language whether you need French Canadian French. You have to put the language. They have a disclaimer you have to accept the disclaimer agree.
Honda Acura Software Installation And Subscription: How To Install it (Window 10 and Up) If you want to download the software, you are going to click here if they ask to put the password for registration. There is also a software installation instruction pdf. You will download Honda Download Manager on your desktop, install the Download Manager.exe Then run Download Manager Those are the software that are going to be updated and downloaded you can click Honda Donwload Manager tool to see what is going on with the downloading and upgrade It will give you all the steps when you download for the first time. After that you can use a passthru device to do anything you want.
Part II: Set up J2534 Passthru, Diagnose and Program Honda/Acura with iHDS Run iHDS Diagnostic System software Select a J2534 Passthru: DST-i, DST-nano, GNA600, Autel MaxiFlash VCI/JVCI, VXDIAG VCX SE, Honda HIM etc Then you can do Immobilizerm ECM, PCM, PMCS, IMOES, PGM-FI etc programming, check manual here:
For 2022.06 or other versions of MB SD C4/C5 Xentry OpenShell XDOS that require you to enter login user name and password to access Xentry, follow 2 ways to login Xentry offline.
Method 1: Login with User Name and Password
Run XENTRY Diagnosis Cars-Offline program on the desktop Input Xentry offline login User Name: Xentry and password:123456 Login successfully To clone Xentry program, click “X” on the top right corner and Press Yes to exit Xentry Diagnosis. *You have to input login user name and password every time you run Xentry Diagnosis if use Method 1.
Method 2 does not require login password. Method 2: Login by replacing XentryService File First of all, download XentryService File here https://mega.nz/folder/5tchia4b#gXt9kvWltn9P_SczyYgmPg Go to C:/Program Files (x86)/Mercedes-Benz/Xentry/XD_MB/bin folder Copy and Replace the XentryServices.xml file download above to C:/Program Files (x86)/Mercedes-Benz/Xentry/XD_MB/bin folder Go to C:/Program Files (x86)/Mercedes-Benz/Xentry/XD_DT/bin folder Then you can run Xentry car or trunk diagnosis program directly without login NOTE: If use method 2, MUST run Diagnosis Stop on the desktop to close Xentry Diagnosis software.
Read also: http://blog.obdii365.com/2022/07/27/activate-2022-06-mb-star-xentry-wis-epc-dts/ |
AuthorCategories |